- #Terasic usb blaster drivers download how to#
- #Terasic usb blaster drivers download install#
- #Terasic usb blaster drivers download serial#
- #Terasic usb blaster drivers download update#
- #Terasic usb blaster drivers download windows 10#
I will choose the driver to install and click Next.
#Terasic usb blaster drivers download update#
If it is impossible to update the usb blaster driver ,we recommend you to modify the JTAG circuit on your board, and adjust the pull-up resistor of TCK TMS to modify jtag timing.Driver Installation for All Versions of Quartus II Software Except Versions 6.1 to 7.2 Uninstall the current usb blaster driver, then try to update the driver to the higher version, such as usb blaster driver for 17.1 or later version.Ģ.
pof file to his own board under Quartus II 11.0SP1 successfully,however, when he checked the Verify tab, it failed to download and reported that "verification failed for device number 1" ,how should I solve the problem?Ī: You can try the following approaches to solve this problem:ġ. sof file to the MAX 10 device first, then download the pof file into the device with the board keeping powering on.Ĩ. pof file to the MA10 device (for self-designed board), it failed and reported the following errors, why did this happen?Ī:It may be caused by the MAX10 device.
#Terasic usb blaster drivers download windows 10#
And you can use either of the Quartus software version later than 10.1 to work with the Windows 10 64-bit.Ħ. Q: What is the operating temperature specification of the UBT?Ī:The UBT is designed to operate in the commercial temperature range (0 to 85C).ĥ.Q: Will USB-Blaster work under Windows 10 64-bit?Ī: Yes, the USB-Blaster work under Windows 10 64-bit. Please note that UBT can't detect the JTAG chain on the Intel Arria 10 GX FPGA Development Kit.Ĥ. Q: What is the difference between the UBT and Altera USB Blaster Download Cable (UBA)?Ī: The main difference is the JTAG circuit, Terasic UBT supports JTAG voltage 2.5v~3.3V, the Altera USB Blaster supports 1.8V~3.3V, they are compatible with other features. Q: What is the TCK Clock Frequency for UBT and AUB2 respectively?Ī: The USB Blaster Cable works with the Jtag clock 6M, while the USB Blaster II Cable works at 24M.ģ. The AUB2 (USB-Blaster II Download Cable) supports USB Blaster II circuit and JTAG Voltage: 5.0-V TTL, 3.3-V LVTTL/LVCMOS ,Single-ended I/O standards from 1.5 V to 3.3 V.Ĭustomers can refer to Intel Cyclone 10 LP device handbook: and check your board JTAG voltage to see which cable is compatible with their board.Ģ. Q:What is the difference between UBT and AUB2?Ī: The main difference is the JTAG circuit, the UBT(USB Blaster Download Cable) supports USB Blaster I circuit and JTAG Voltage: 2.5V ~ 3.3V.
#Terasic usb blaster drivers download serial#
If Altera USB Blaster isn’t showed in Universal Serial Bus controllers, please check whether the Other devices has Unknown device.If yes, users can use Quartus programmer and download FPGA code. Power on the FPGA board and connect USB blaster port or USB blaster cable to PC.Ĭheck if the Universal Serial Bus controllers in the Windows Device Manager has an Altera USB Blaster.
#Terasic usb blaster drivers download how to#
This section describes users how to test whether the on-board USB blaster or USB blaster cable is properly installed and operated Using USB Blaster Under Linux USB Blaster Self Test Prime Signal Tap Logic Analyzer for logic analysis.Īltera_USB_Blaster_Driver_Installation_Instructions You can also use the cable with the Intel Quartus The Terasic Download Cable and initiate the programming or configuration using To program or configure the device, connect the host system to the device board using System and set up the hardware in the Intel Quartus® Prime software. To start using the Intel FPGA Download Cable, user need to install the drivers on your Target power supplied by the device boardĭimension of the Terasic USB Download Cable
The following picture and table list the pins of the Terasic Download Cable female plug andĭescribes their functions in the JTAG and passive serial modes. Table 1‑4 Support Target board supply voltage Support Target board supply voltage